Modem-Dialup-NT HOW-TO Al Dev (Alavoor Vasudevan) alavoor[AT]yahoo.com v1.7, 22 June 2002 ------------------------------------------------------------------------------- This document will help you to setup the Modem to do Dial-up Networking with remote server like Windows NT RAS or Linux RAS (Remote Access Server). You can use the Modem to do Dial-Up Networking on Linux very similar to that of MS Windows dialup networking. ------------------------------------------------------------------------------- 1. Introduction (The latest version of this document is at http:// www.milkywaygalaxy.freeservers.com. You may want to check there for changes). Most of the companies in USA and Europe provide "Remote Access Servers" (RAS), so that their employees can dial-in from remote locations either from home or from field. RAS servers are generally Linux RAS servers or MS Windows NT RAS servers. Nowadays, Virtual Private Network (VPN) is becoming quite popular because it supports broadband and may eventually replace dial-up networking which is very slow running at 56KB/sec. See the VPN_HOWTO and VPN-Masquerade_howto and java based MindTerm-SSH-HOWTO. Configuring a dial-up connection on Linux is about as simple as it is in Windows. We will use PPP. Definition: PPP ('Point to Point Protocol') is a protocol, that makes it possible to make IP-Links (Internet Protocol) between two computers with a modem. The operating system Linux has this protocol in the kernel (If you compiled it into the kernel). For a ppp-link you need to start a daemon called pppd. With PPP you can make a link between two hosts which understand the protocol. A link between a Linux host, acting as client and a Windows NT server, acting as server, is called a (Microsoft term) 'Remote Access Service' (RAS) link. First, see if your modem is supported by linux. Internal Modems (WinModems) may work with Linux because they need extra software drivers to make it work with Linux. Test your WinModem to see if it works under Linux. Some WinModems require special tweaking to make it work in Linux. 1.1 Preparations Check if you have all the needed hardware, software and data and hand: * A modem supported by Linux. Some modems, like most internal PCI modems or some external USB modems are so-called WinModems. Which means that they rely on Windows-only software to work. Read Winmodems_are_not_modems for more information and a compability list and check out Linmodems.org for (a few) drivers. * The modem's init-string. GNU/Linux does not have an equivalent to the Windows hardware information file (.inf) mechanism. You may have to find out the init-string for your modem yourself. It should(TM) be listed in your hardware's documentation or in the modem's INF file, but there are also online sources like this list_of_modem_init-strings . If you have no clue at all, use ATZ, that works with many modems. * Provider data. You'll need your login name, password and the telephone number. DNS addresses would be fine, too, but are optional for recent versions of pppd. * Check if your modem is connected correctly to the system or properly recognized by it. With an external modem, that's pretty easy. As 'root' do echo >/dev/ttyS0 and watch the modem LEDs. You should see them flicker for a moment. If not, try echo >/dev/ttyS1 in case your modem is connected to the second serial port. With an internal modem, use HardDrake to check if the system sees the modem. Or use this command to query the PCI list directly: cat /proc/pci. If it's an ISA bus modem, check '/etc/isapnp.conf' if it is listed there. If you don't have that file, you'll have to generate it. Read isapnpfaq.txt in the isapnptools doc directory or man isapnp or man isapnp.conf. 2. Dial-up ISP Internet Connection Follow these steps to connect to your ISP via dial-up modem: * You should have installed the packages kdenetwork-ppp*.rpm and ppp*.rpm * At bash prompt type '/usr/bin/kppp'. This will bring up the KPPP dialog boxes. * On 'Accounts' tab setup the 'New Connection', and click the following tabs: 1. On 'Dial' tab use Authentication='PAP/CHAP', yes to 'Store Password' 2. On 'IP' tab select 'Dyanamic IP Address' and uncheck 'Auto-configure hostname' 3. On 'Gateway' tab select 'Default Gateway' and check 'Assign the Default Route' 4. On 'DNS' tab select 'Configuration Automatic' and check 'Disable existing DNS' 5. On 'Login Script' tab - do nothing here 6. On 'Execute' tab - do nothing here 7. On 'Accounting' tab - do nothing here * On 'Device' tab select the proper modem device like ttyS1(com1), ttyS2 (com2) * On 'Modem' tab 'Query Modem' to see the results. If no results come up, go to device tab and pick the proper device. * Enter login ID and password and connect. After doing the above steps, you would have connected to internet. To test do: ------------------------------------------------------------------------------- bash$ ping www.yahoo.com PING www.yahoo.com(66.218.71.83) from 64.152.245.119 : 56(84) bytes of data. 64 bytes from www.yahoo.com (66.218.71.83): icmp_seq=0 ttl=58 time=236.931 msec 64 bytes from www.yahoo.com (66.218.71.83): icmp_seq=1 ttl=58 time=229.074 msec bash$ ping www.google.com bash$ su - root # ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 ppp0 Link encap:Point-to-Point Protocol inet addr:64.158.37.63 P-t-P:209.244.43.188 Mask:255.255.255.255 # netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 209.244.43.183 0.0.0.0 255.255.255.255 UH 40 0 0 ppp0 127.0.0.0 0.0.0.0 255.0.0.0 U 40 0 0 lo 0.0.0.0 209.244.43.183 0.0.0.0 UG 40 0 0 ppp0 ------------------------------------------------------------------------------- You will see the listing like above. If you are not able to do 'ping www.yahoo.com' or 'ping www.google.com' then there is some trouble. See the next section 'Troubleshooting' 2.1 Troubleshooting ISP Connection If you are getting the connection and getting the local IP address and Remote IP address from KPPP dialer but you are not able to do ping on a remote host like 'ping www.yahoo.com' then do: ------------------------------------------------------------------------------- bash$ su - root # ifconfig See the listing above and temporarily disable other interfaces like eth0, eth1 # ifconfig eth0 down # ifconfig eth1 down # ifconfig eth2 down # ifconfig This should list only ppp0 and lo ------------------------------------------------------------------------------- Once other interfaces like eth0, eth1, eth2 are disabled, now disconnect and reconnect with KPPP dialer. After the connection to internet is successful, you can re-enable other interfaces as below: ------------------------------------------------------------------------------- bash$ ping www.yahoo.com If connection is okay, then do: bash$ su - root # ifconfig eth0 up # ifconfig eth1 up # ifconfig eth2 up # ifconfig ------------------------------------------------------------------------------- If you still have problems then refer to the KPPP user guides and FAQs as below: ------------------------------------------------------------------------------- $ rpm -ql kdenetwork-ppp $ cd /usr/share/doc/HTML/en/kppp $ docbook2html kppp-faq.docbook 1> kppp-faq.html $ docbook2html index.docbook 1> index.html ------------------------------------------------------------------------------- 3. Quick Steps to Dialup Networking These quick steps will enable you to setup dial-up networking on Linux in just five minutes. You need the following packages: * wvdial*.rpm * ppp*.rpm You can check with rpm -qa | grep -i wvdial for the installed packages on redhat linux. Use equivalent package commands in case of other distributions like Debian or Slackware. The steps below are for MS Windows NT RAS server. The NT RAS requires noauth in wvdial file. The Linux RAS may need different settings. In the sample example given below, you should replace username john with the user ID given to you to login into remote RAS server. 1. Edit the file /etc/wvdial.conf and insert lines like -------------------------------------------------------------------------- [Dialer myconnection] Username = john Password = passwordofjohn Phone = 982 1956 Area Code = 713 Inherits = Dialer Defaults Stupid mode = 1 -------------------------------------------------------------------------- Change john with whatever. 2. Edit /etc/ppp/pap-secrets and insert lines like -------------------------------------------------------------------------- # Secrets for authentication using PAP # client server secret IP addresses john ppp0 passwordofjohn john * passwordofjohn -------------------------------------------------------------------------- Change john with whatever. 3. Edit /etc/ppp/chap-secrets and insert lines like -------------------------------------------------------------------------- # Secrets for authentication using CHAP # client server secret IP addresses john ppp0 passwordofjohn john * passwordofjohn -------------------------------------------------------------------------- Change john with whatever. 4. Edit /etc/ppp/options and insert lines like -------------------------------------------------------------------------- lock defaultroute noipdefault idle 1200 usepeerdns proxyarp -------------------------------------------------------------------------- 5. Create a new file /etc/ppp/ip-up and insert lines like -------------------------------------------------------------------------- #!/bin/bash # This file /etc/ppp/ip-up should not be modified -- make local changes to # /etc/ppp/ip-up.local instead LOGDEVICE=$6 REALDEVICE=$1 export PATH=/sbin:/usr/sbin:/bin:/usr/bin [ -f /etc/sysconfig/network-scripts/ifcfg-${LOGDEVICE} ] && / etc/sysconfig/network-scripts/ifup-post ifcfg-${LOGDEVICE} [ -x /etc/ppp/ip-up.local ] && /etc/ppp/ip-up.local "$@" exit 0 -------------------------------------------------------------------------- 6. Create a new file /etc/ppp/ip-up.local and insert lines like -------------------------------------------------------------------------- #!/bin/sh echo " " echo "Before doing route add......" echo "Output from netstat -nr is : " netstat -nr echo " " echo " Doing route add now.... " # You should change the lines below and add the networks where # your remote machines are ... route add -net 156.15.24.0 netmask 255.255.255.0 dev ppp0 route add -net 172.28.36.0 netmask 255.255.255.0 dev ppp0 route add -net 172.28.39.0 netmask 255.255.255.0 dev ppp0 route add -net 172.28.26.0 netmask 255.255.255.0 dev ppp0 echo "After doing route add......" echo "Output from netstat -nr is : " netstat -nr echo " " -------------------------------------------------------------------------- When wvdial is started it automatically starts the pppd which automatically calls this script to add route to your remote networks via the PPP link. See 'man pppd'. In the example above I have to connect to remote networks 156.15.24, 172.28.36, 172.28.39 via the PPP link. You should replace these with your settings. You can also manually add or delete the route after starting the PPP. -------------------------------------------------------------------------- bash$ su - root bash# route add -net 172.28.26.0 netmask 255.255.255.0 dev ppp0 bash# route del -net 172.23.2.0 netmask 255.255.255.0 dev ppp0 -------------------------------------------------------------------------- 7. Create a new file /etc/ppp/ip-down and insert lines like -------------------------------------------------------------------------- #!/bin/bash # This file /etc/ppp/ip-down should not be modified -- make local changes to # /etc/ppp/ip-down.local instead LOGDEVICE=$6 REALDEVICE=$1 export PATH=/sbin:/usr/sbin:/bin:/usr/bin [ -x /etc/ppp/ip-down.local ] && /etc/ppp/ip-down.local "$@" /etc/sysconfig/network-scripts/ifdown-post ifcfg-${LOGDEVICE} exit 0 -------------------------------------------------------------------------- 8. Create a new file /etc/ppp/ip-down.local and insert lines like -------------------------------------------------------------------------- #!/bin/sh echo " " echo "Before doing route delete ......" echo "Output from netstat -nr is : " netstat -nr echo " " echo " Doing route delete now.... " # Lines below should be same as in ip-up.local but with delete route del -net 156.15.24.0 netmask 255.255.255.0 dev ppp0 route del -net 172.28.36.0 netmask 255.255.255.0 dev ppp0 route del -net 172.23.2.0 netmask 255.255.255.0 dev ppp0 echo "After doing route delete ......" echo "Output from netstat -nr is : " netstat -nr echo " " -------------------------------------------------------------------------- When pppd is stopped it automatically calls this script to clean up whatever ip-up script did. See 'man pppd'. 9. Edit /etc/ppp/peers/wvdial and insert lines like -------------------------------------------------------------------------- noauth user john name wvdial -------------------------------------------------------------------------- Change john with whatever. 10. If you have an external modem, then just before dialing, switch off/on the power to modem to reset it. -------------------------------------------------------------------------- bash$ su - root bash# tail -f /var/log/messages Bring up another xterm shell window and bash$ su - root bash# man pppd bash# man wvdial bash# cd /etc/ppp bash# nohup wvdial myconnection & bash# tail -f nohup.out Bring up another xterm shell window and bash$ su - root bash# ifconfig -a And you should see ppp device listed and up and running. bash# netstat -nr And you should see ppp device listed along with other interfaces. -------------------------------------------------------------------------- 11. By this step the pppd should have established the routes to remote networks with ip-up.local script. Also pppd should have created the /etc/ ppp/resolv.conf for DNS servers. Now, try connect to remote host and verify connections. -------------------------------------------------------------------------- bash$ su - root bash# tail -100 /var/log/messages | less bash# cat /etc/ppp/resolv.conf bash# ifconfig -a bash# netstat -nr I looked for route to network 156.15.24.0 (You should see your network as per /etc/ppp/ip-up.local) bash# ping 156.15.24.68 bash# telnet 156.15.24.68 You can also edit /etc/hosts and add these hosts 156.15.24.64 starship 172.28.36.131 gemstone bash# ping starship bash# ping gemstone bash# telnet gemstone bash# ftp gemstone -------------------------------------------------------------------------- 12. To stop the PPP : -------------------------------------------------------------------------- bash$ su - root bash# killall wvdial bash# killall pppd bash# man killall -------------------------------------------------------------------------- 13. Now enable non-root user to do dial-up networking with PPP. Make sure that the user belongs to the groups `uucp' and `dialout'. -------------------------------------------------------------------------- bash$ su - root bash# su - someuser bash$ id uid=501(someuser) gid=501(maingid) groups=501(maingid),503 (staroffice),505(staff) This shows the groups 'someuser' belongs. bash$ exit bash# usermod --help bash# usermod -g maingid -G staroffice,staff,uucp,dialout someuser bash# chgrp -R uucp /etc/ppp bash# chmod -R ug+r /etc/ppp bash# chmod -R o-rwx /etc/ppp bash# chmod go-rwx /etc/ppp/*secrets bash# chmod u+s /usr/sbin/pppd bash# su - someuser bash$ id This will display groups someuser belongs and you should see uucp. bash$ nohup wvdial myconnection & bash$ tail -f nohup.out -------------------------------------------------------------------------- It is very strongly recommended that you use wvdial as `normal' user, and make sure that the user belongs to the groups `uucp' and `dialout'. 14. See also the frontend tool for wvdial at X-wvdial. 15. If you do not have any other interface ethernet cards for Cable modem or DSL modem then you can setup telephone dial-up modem as the default route for all outside conections to internet. Assuming you only have modem connection via POTS (Plain Old Telephone System) you can do - -------------------------------------------------------------------------- bash$ su - root bash# man route bash# ifconfig -a And look for the IP address of the ppp device, and use it below bash# route add default gw IP_of_ppp_device For example - bash# route add default gw 172.28.36.3 -------------------------------------------------------------------------- 3.1 Troubleshooting In case you have problems: ------------------------------------------------------------------------------- bash$ su - root bash# tail -f /var/log/messages And then start myconnection in /etc/wvdial.conf bash# wvdial myconnection bash# ifconfig -a Should list ppp bash# netstat -nr Should list ppp If you have multiple interfaces, like ethernet cards to DSL or Cable modem, to check which route is being used, do: bash# traceroute www.yahoo.com bash# traceroute remotehostname ------------------------------------------------------------------------------- 3.2 Graphical Tools Preference should be given the console line commands as in previous section, but some people prefer GUI interface. You can use graphical tools like Linuxconf, KPPP, GnomePPP and many others. Note: I very strongly recommend using command-line console commands 'wvdial' as demonstrated in previous sections, as they are lot simpler and easy to use. ------------------------------------------------------------------------------- bash$ su - root bash# linuxconf & And select Networking->Client Tasks->Routing & Gateways->Set Other Routes to networks->Add network . Also select Networking->PPP bash# rp3 & bash# rp3-config & ------------------------------------------------------------------------------- 4. Remote connection with VNC Once you have connection through PPP to remote machines, you can use the VNC to display remote machines on your local display. * The VNC is at http://www.uk.research.att.com/vnc * Get VNC rpms from rpmfind. * The best Window manager for VNC is QVWM which is like MS Windows 98/NT/2000 interface, get it from http://www.qvwm.org. * After starting vncserver, you can start the vncviewer program on clients like MS Windows, Mac or Linux. * See also the List_of_X11_Windows_Managers. Compiling qvwm on Solaris : On Solaris you should install the following packages which you can get from http://sun.freeware.com - xpm, imlib, jpeg, libungif, giflib, libpng, tiff. And you can download the binary package for solaris from http://www.qvwm.org. Or you can download the qvwm source for solaris from http://www.qvwm.org and compile it using gcc. Troubleshooting compile: You should put unsigned long before arg in usleep() usleep((unsigned long) 10000) 4.1 Microsoft "MS Outlook" Email from PPP Method 1 : 1. At office, start VNC server on your Windows NT/2000 desktop. 2. Connect from home using modem via PPP. 3. Once the PPP is established, you can start the vncviewer program. Just type /usr/bin/vncviewer. 4. Enter your office Windows NT/2000 desktop's hostname and vnc password 5. The entire desktop of your remote office Windows NT/2000 is displayed. Now you can read your MS Outlook email. Method 2 : * Bynari_InsightClient Go here click on products->Insight Connector Outlook. Client for MS Exchange server and MS Outlook, * CrossOver_Office has MS Outlook, * Ximian_Connector for MS Outlook/Exchange, * Ximian_Evolution MS Outlook killer, * Mahogany rated best * GNOME_Balsa mail client rated 2nd best * KDE_KMail rated 3rd best * PINE rated 4th Method 3 : Web based * POSTACI rated best * SquirrelMail rated 2nd best * IMP_Horde rated 3rd best ( horde_rpm rated 4th best * imp_rpm) * 6XMailer * Netmania_mail * NOCC 5. Setup RAS server For details on RAS please see RAS_Buyer's_Guide and the RAS product Cyclades PR4000 A Remote Access Server (RAS) is a network box that connects remote dialup clients to a Local Area Network (LAN. RAS are used by Internet Service Providers (ISP) and Corporate Network Managers to allow home users, small offices, and telecommuters to connect to the Internet or the corporate LAN from remote sites using analog phone lines or ISDN lines. Since the mid-90's, with the popularization of the Internet, the demand for dialup remote access has been growing exponentially. Until faster options are broadly available, analog phone lines and ISDN lines are the more common media to remotely connect personal computers or home offices to the LAN or to the Internet. A RAS is a box that attaches to the LAN at the central site and provides connection to dialup lines. It allows remote clients to access the LAN (and possibly the Internet) by using modems or ISDN terminal adapters. In the past, RS-232 Terminal Servers were used to provide remote access. A server-based or stand-alone box would attach to the LAN and provide multiple RS-232 serial interfaces. Those serial ports were connected to a modem bank, which on its turn, connected to the analog phone lines coming into the building. With the crescent demand, the number of required phone lines started to grow to a point where it was impractical to increase their number at the central site. The phone company, instead of delivering individual phone lines to you, bundle 23 or 30 channels in one T1 or E1 ISDN-PRI line. Typically, a RAS will have one or more Ethernet ports for connection to the LAN and one or more T1/E1/ISDN-PRI ports for the incoming calls (a T1/ISDN-PRI line is equivalent to 23 phone lines, while an E1/ISDN-PRI line is equivalent to 30 phone lines). A RAS will typically have internal digital modems and will be able to terminate both analog and digital calls and connect to remote clients using Point-to- Point (PPP) protocol. 5.1 Stand-alone or Server-Based ? Traditionally, RAS are stand-alone, integrated and self-contained boxes running an Internetworking Operating System on a proprietary hardware specifically designed for Remote Access. They connect to the LAN and to the income dialup lines and all you need to do is to configure them properly to get them working. But there is also the possibility of building a RAS using standard server hardware (usually a PC) with a Networking Operating System (typically, Linux or Windows). The user installs PCI RAS adapter (with digital modems and ISDN-PRI interfaces) in a PC server, install the OS and the proper device drivers and configure the system to work as a Remote Access Server. So, maybe the first question you face when selecting a RAS solution is this: Stand-alone or server-based? In general, stand-alone solutions are better for the average user because of the following factors: Integration: The RAS solution is complete and there is no need for software or hardware integration. That eliminates the possibility of hardware and software incompatibilities and installation problems and gives you a single point of contact for technical support and problem solving. Reliability: Stand-alone solutions run on hardware and software that was specifically designed for remote access. They are more integrated, more compact, dissipate less power, and, because of that, are more reliable than a solution based on general-purpose components. Cost: Usually, commodity PC hardware and open source software tend to drive costs down, making server-based solutions attractive for technical users who already have the PC and are willing to face the potential problems of integrating the solution from standard components. But, the PCI adapters for RAS available in the market today still carry a price tag that makes it difficult to justify a server-based solution. 6. Related URLs * The best document is : Mandrake_Dial_up_networking * Suse_PPP_wvdial_document and PPP_categories * PPP_HOWTO * PPP-NT-HOWTO * Modem_HOWTO * ISP_Hookup_HOWTO:_Chapter_6 * Simple RAS server to provide internet connectivity http:// simpleras.sourceforge.net * Linux_PPP_FAQ * PPP_Design_&_Debugging * Suomeksi_PPP_page * Unix_Serial_Port_Resources * Linux_Dial-in_server - Setup guide. * List_of_PPP_utilities go here and type "ppp" in the search box. * General_PPP_and_IPX_over_PPP * VPN_HOWTO * VPN-Masquerade_howto * Java based MindTerm-SSH-HOWTO Linux goodies main site is at http://24.221.230.253 and secondary site at http: //www.milkywaygalaxy.freeservers.com Mirror sites are at - angelfire, geocities, virtualave, Fortunecity, Freewebsites, Tripod, 101xs, 50megs, 7. Other Formats of this Document This document is published in 14 different formats namely: DVI, Postscript, Latex, Adobe Acrobat PDF, LyX, GNU-info, HTML, RTF(Rich Text Format), Plain- text, Unix man pages, single HTML file, SGML (Linuxdoc format), SGML (Docbook format), and MS WinHelp format. This howto document is located at: * http://www.linuxdoc.org and click on HOWTOs and search for the howto document name using CTRL+f or ALT+f within the web-browser. You can also find this document at the following mirrors sites: * http://www.caldera.com/LDP/HOWTO * http://www.linux.ucla.edu/LDP * http://www.cc.gatech.edu/linux/LDP * http://www.redhat.com/mirrors/LDP * Other mirror sites near you (network-address-wise) can be found at http:// www.linuxdoc.org/mirrors.html select a site and go to directory /LDP/HOWTO/ xxxxx-HOWTO.html * You can get this HOWTO document as a single file tar ball in HTML, DVI, Postscript or SGML formats from - ftp://www.linuxdoc.org/pub/Linux/docs/ HOWTO/other-formats/ and http://www.linuxdoc.org/docs.html#howto * Plain text format is in: ftp://www.linuxdoc.org/pub/Linux/docs/HOWTO and http://www.linuxdoc.org/docs.html#howto * Single HTML file format is in: http://www.linuxdoc.org/docs.html#howto A single HTML file can be created with the command (see man sgml2html) - sgml2html -split 0 xxxxhowto.sgml * Translations to other languages like French, German, Spanish, Chinese, and Japanese are in ftp://www.linuxdoc.org/pub/Linux/docs/HOWTO and http:// www.linuxdoc.org/docs.html#howto Any help from you to translate to other languages is welcome. The document is written using a tool called "SGML-Tools" which can be got from: http://www.sgmltools.org Compiling the source you will get the following commands like: * sgml2html xxxxhowto.sgml (to generate html file) * sgml2html -split 0 xxxxhowto.sgml (to generate a single page html file) * sgml2rtf xxxxhowto.sgml (to generate RTF file) * sgml2latex xxxxhowto.sgml (to generate latex file) 7.1 Acrobat PDF format A PDF file can be generated from postscript file using either acrobat distill or Ghostscript. And a postscript file is generated from DVI which in turn is generated from a LaTex file. You can download distill software from http:// www.adobe.com and from unix and from windows . Given below is a sample session: ------------------------------------------------------------------------------- bash$ man sgml2latex bash$ sgml2latex filename.sgml bash$ man dvips bash$ dvips -o filename.ps filename.dvi bash$ distill filename.ps bash$ man ghostscript bash$ man ps2pdf bash$ ps2pdf input.ps output.pdf bash$ acroread output.pdf & ------------------------------------------------------------------------------- Or you can use the Ghostscript command ps2pdf. ps2pdf is a work-alike for nearly all the functionality of Adobe's Acrobat Distiller product: it converts PostScript files to Portable Document Format (PDF) files. ps2pdf is implemented as a very small command script (batch file) that invokes Ghostscript, selecting a special "output device" called pdfwrite. In order to use ps2pdf, the pdfwrite device must be included in the makefile when Ghostscript was compiled; see the documentation on building Ghostscript for details. 7.2 Convert Linuxdoc to Docbook format This document is written in linuxdoc SGML format. The Docbook SGML format supercedes the linuxdoc format and has a lot more features than linuxdoc. The linuxdoc is very simple and easy to use. To convert linuxdoc SGML file to Docbook SGML use the program ld2db.sh and some Perl scripts. The ld2db output is not 100% clean and you need to use the clean_ld2db.pl Perl script. You may need to manually correct a few lines in the document. * Download the ld2db program from http://www.dcs.gla.ac.uk/~rrt/docbook.html or from Milkyway_Galaxy_site * Download the cleanup_ld2db.pl perl script from from Milkyway_Galaxy_site The ld2db.sh is not 100% clean, so you will get some errors when you run it. ------------------------------------------------------------------------------- bash$ ld2db.sh file-linuxdoc.sgml db.sgml bash$ cleanup.pl db.sgml > db_clean.sgml bash$ gvim db_clean.sgml bash$ docbook2html db.sgml ------------------------------------------------------------------------------- And you may have to manually edit some of the minor errors after running the Perl script. For example you may need to put closing tag < /Para> for each < Listitem> 7.3 Convert to MS WinHelp format You can convert the SGML howto document to a Microsoft Windows Help file, First convert the sgml to html using: ------------------------------------------------------------------------------- bash$ sgml2html xxxxhowto.sgml (to generate html file) bash$ sgml2html -split 0 xxxxhowto.sgml (to generate a single page html file) ------------------------------------------------------------------------------- Then use the tool HtmlToHlp. You can also use sgml2rtf and then use the RTF files for generating winhelp files. 7.4 Reading various formats In order to view the document in dvi format, use the xdvi program. The xdvi program is located in tetex-xdvi*.rpm package in Redhat Linux which can be located through ControlPanel | Applications | Publishing | TeX menu buttons. To read a dvi document give the command: xdvi -geometry 80x90 howto.dvi man xdvi And resize the window with the mouse. To navigate use Arrow keys, Page Up, Page Down keys, also you can use 'f', 'd', 'u', 'c', 'l', 'r', 'p', 'n' letter keys to move up, down, center, next page, previous page etc. To turn off expert menu press 'x'. You can read a postscript file using the program 'gv' (ghostview) or 'ghostscript'. The ghostscript program is in the ghostscript*.rpm package and the gv program is in the gv*.rpm package in Redhat Linux which can be located through ControlPanel | Applications | Graphics menu buttons. The gv program is much more user friendly than ghostscript. Also ghostscript and gv are available on other platforms like OS/2, Windows 95 and NT. You can view this document even on those platforms. * Get ghostscript for Windows 95, OS/2, and for all OSes from http:// www.cs.wisc.edu/~ghost To read a postscript document give the command: gv howto.ps ghostscript howto.ps You can read an HTML format document using Netscape Navigator, Microsoft Internet explorer, Redhat Baron Web browser or any of the 10 other web browsers. You can read the latex, LyX output using LyX an X Window front end to LaTex. 7.5 Convert HTML to SGML html2sgml To convert any HTML document to Linuxdoc SGML use the tool 'html2sgml' from http://www.abc.se/~m9339/prog/html2sgml.html. 8. Copyright Copyright policy is GNU/GPL as per LDP (Linux Documentation project). LDP is a GNU/GPL project. Additional restrictions are - you must retain the author's name, email address and this copyright notice on all the copies. If you make any changes or additions to this document then you should intimate all the authors of this document. 9. Appendix A Connecting Linux + PPP < -- > NT + RAS... This section is written by John Newbigin, Email: jn@it.swin.edu.au Below is extract from http://uranus.it.swin.edu.au/~jn/linux/ppp/linuxppp.htm See also PPP_HOWTO * Part 1... The easy bit : Use minicom or your favourite terminal program to dial the NT RAS Server. Once you have a connection you can proceed to Part 2. Make sure you can quit your terminal without resetting the modem. * Part 2... The harder bit : Setting up the /etc/ppp/options file may be a bit tricky. The important things to do are... Make sure you do not have any of the following entries: o auth #This will demand that the NT machine authenticate it's self to your machine, this is generally not possible, or needed o +pap #This will demand that the NT machine authenticates it's self using PAP, see above o -pap #This says that you won't agree to use PAP o +chap #This will demand that the NT machine authenticates it's self using CHAP, see above Make sure the RAS server will accept plain text passwords. You need this to use PAP authentication. This can be set by going to Control Panel -> Network -> Services -> Remote Access Service -> Properties. Select the modem or dial up device, go to Network -> Server Settings -> Encryption Settings and select "allow any authentication including plain text". Then hit OK, Save etc. to close it all. * Part 3... The hardest bit (without this document) : NOTE: If you use my pppd patch, you will not have to do this In the /etc/ppp/pap-secretes file, add the following lines: ----------------------------------------------------------------------------- "" * "" "jn" * "MyPassword" ----------------------------------------------------------------------------- Where jn is your user name on the NT machine. But what if you are a member of a domain? Then use this instead (where csse-mm is replaced with your domain name) ----------------------------------------------------------------------------- "" * "" "csse-mm\\jn" * "MyPassword" ----------------------------------------------------------------------------- Note that you must escape the "\" character as "\\". then, back to the /etc/ ppp/options file and add the following line: ----------------------------------------------------------------------------- name "jn" or name "csse-mm\\jn" ----------------------------------------------------------------------------- depending what you put in the pap-secretes file. * Part 4... Another easy bit : Dial in to the server, like in step one, or using your custom script. Start ppp with the following line: pppd 115200 / dev/cua1 or whatever your settings might be. You may want to enable debug information if something does not work, but everything should. Run "ifconfig" and you should see an entry for ppp0. If you do then you are cooking with gas. Restart pppd using the "defaultroute" option and start surfing the internet. If you are still having trouble, or can't understand any of these instructions, drop me an e-mail John Newbigin ( jn@it.swin.edu.au ).