[LinuxFocus-icon]
LinuxFocus article number 369
http://linuxfocus.org

[Photo of the Author]
by Guido Socher (homepage)

About the author:

Guido likes Linux because it is a really good system to develop your own hardware.

Part 2 -- A digital thermometer or talk I2C to your atmel microcontroller

[Illustration]

Abstract:

In this second part of the article we will connect a LCD display and I will explain how the software works.

Those readers who are new to this series should first read the first part (February2005 article365).

_________________ _________________ _________________

 

The new things

In the previouse article we build already most of the hardware and the main functionality for temperature measurement and transmission of the data to a Linux PC. In this article a LCD display and a very simple gtk GUI will be added.

Adding these two things is very easy to do. I will therefore spend the rest of the article to explain how the I2C software and the analog to digital converter works.  

The LCD display

For the LCD display we use a HD44780 compatible display as it was already used in previous articles. These displays are very easy to use in combination with microcontrollers because you can send them ASCII characters.
HD44780 compatible LCD display

As for all articles in this series you can again get all the parts including the LCD display at shop.tuxgraphics.org
I use the same LCD driver code as in all previous articles. The files which implement this LCD driver are lcd.c lcd.h and lcd_hw.h. They are in the package which you can download at the end of this article. The interface for this code is really easy to use:
// call this once:
// initialize LCD display, cursor off
lcd_init(LCD_DISP_ON);

// to write some text we first clear
// the display:
lcd_clrscr();
lcd_puts("Hello");
// go to the second line:
lcd_gotoxy(0,1);
lcd_puts("LCD");
How those HD44780 displays work is described in the linuxfocus September2002 article "Understanding HD44780 compatible LCD-displays"

The software is written such that it works with both 16x2 and 20x2 LCD displays.

board change There is also an update to the circuit diagram. I discovered that some LCD displays have a higher capacitive load and lower resistance than others. This is probably because they have a better ESD protection. This additional load can possibly cause bit errors during the In Circuit Programming when the LCD display is connected to the SCK and MOSI pins.

As a first solution I tried to connect additional resistors into the lines to the LCD display. This worked for me but some people, especially laptop users still had problems.

To avoid this problem all together I updated the circuit diagram and the D7 and RS pins of the LCD display are now connected to PD7 and PD6. It is not a problem to change this even if you have made the board already. Just add a little wire under the board and cut the connection to PB3 with a knife.

Circuit diagram

 

A little GUI

For those wo would like to have GUI on their desktop I made a really simple gui. It consists just of 2 labels which are used to display the two line output of i2ctemp_linux command (the i2ctemp_linux is the command which read the temperatures from the circuit via I2C):
GUI

Now we have a really cool thermometer. With a lot of possibilities: I will now use the rest of this ariticle to explain a bit the internals of the software.  

How it works: Analog to digital conversion

The Atmega8 supports two modes. One where it permanently measures the analog signals and just triggers an interrupt when the measurement is ready. The application software can then use this interrupt to quickly copy the result from two registers into a variable.

The other mode is the so called single shot mode. Here only one conversion is done. The single shot mode is still pretty fast. Including the setup time of the required registers before and the reading out you can still get 100 conversion per second. This is more than fast enough for us. So we use this mode.

On our Atmega8 we can use the analog input pins ADC0 to ADC3. In addition to this there are the pins AGND (analog ground, connected to normal ground), AREF (the reference voltage) and AVCC (connected to +5V).

During analog to digital conversion the analog signal is compared with AREF. An analog signal equal to AREF corresponds to a digital value of 1023. AREF can be any external reference between 0 and 5V. Without the use of an external reference you can still do precise conversion by either using an internal reference (2.56V) or AVCC. What is used is decided in the software via the REFS0 and REFS1 bits in the ADMUX register.

The analog to digital converter can convert one of the input lines ADC0-ADC3 at a time. Before you start conversion you have to set bits in the ADMUX register to tell the chip which channel to use.

A simple analog to digital conversion would then look like this:
volatile static int analog_result;
volatile static unsigned char analog_busy;

analog_busy=1; // busy mark the ADC function
channel=0; // measure ADC0
// use internal 2.56V ref
outp((1<<REFS1)|(1<<REFS0)|(channel & 0x07),ADMUX);
outp((1<<ADEN)|(1<<ADIE)|(1<<ADIF)|(1<<ADPS2),ADCSR);
sbi(ADCSR,ADSC); // start conversion
Now the microcontroller will do the analog to digital conversion and call the function SIGNAL(SIG_ADC) once it is ready. In this function we can copy the result to a variable. As a programmer you must watch out that you read the lower 8 bits first as the microcontroller has some locking mechanism to simulate "atomic" reading.
SIGNAL(SIG_ADC) {
        unsigned char adlow,adhigh;
        adlow=inp(ADCL); /* read low first, two lines. Do not combine
                          the two lines into one C statement */
        adhigh=inp(ADCH);
        analog_result=(adhigh<<8)|(adlow & 0xFF);
        analog_busy=0;
}
After this we have the analog to digital conversion result available as a number in the analog_result variable. This can the be used elsewhere in the program. Very easy.

As for all interrupts you need to call sei(); to globally enable them. This should be done somewhere in the main program (not shown above).

There were a lot if bits and flags which I will shorty explain: The Atmega8 has several possibilities for reference voltage selection. The reference voltage is compared against our analog input voltage. It is the voltage that corresponds to a digital value of 1023.
REFS0=0, REFS1=0use external AREF, Internal Vref turned off
REFS0=0, REFS1=1AVCC with optional external capacitor at AREF pin
REFS0=1, REFS1=1Internal 2.56V Voltage Reference with (optional) external capacitor at AREF pin
An optional capacitor on the AREF pin can be used to suppress noise and stabilize the AREF voltage.

 

How it works: I2C communication, Atmega8 part

I explained already in the part 1 (February2005 article365) how this I2C protocol works. Let's now have a look at the software. The Atmega8 has hardware support for I2C communication. Therefore you do not actually need to implement the protocol. Instead you need to implement a state machine. This tells the Atmega8 what to do next. Here is an example:

An I2C packet with our own slave address was received. The Atmega8 will now call the function SIGNAL(SIG_2WIRE_SERIAL) with the status code 0x60 (for other events we would get other codes).

--> We must now set a number of registers to tell the Atmega8 what to do next. In this case we will tell it: receive the data part and acknowledge it.

When the actual data was received we will get called with status code 0x80.

--> Now we read the databyte and tell the Atmega8 to acknowledge the next data byte if it comes.

When the communication is over we get a status code 0xA0 (stop condition) and we can tell our application that a complete message was received.

The whole state machine for the I2C slave mode and all possible states are explained in the datasheet of the Atmega8 on page 183 (see link in reference section at the end of the article).

Transmitting data is very similar. Have a look at the code!  

How it works: I2C communication, Linux side

i2c input stage First a word about the hardware. Even though I2C is a bus we only use a point to point connection between one slave and the Linux PC as I2C master. We can therefore save the pullup resistor as long as the slave can still pull down the line without causing a short circuit. We just put a 4.7K resistor into the line.

The voltage levels must be adjusted. This done with the Z-diode limiting the negative voltages to -0.7V and the positive voltages to max +5.1.

After reading more about the internals of the Atmeag8 I came meanwhile to the conclusion that the internal protection of the input stages of the Atmeag8 is probably sufficient because the currents through the 4.7K resistor are very low. We don't actually need the Z-diode. It does however not harm to have the Z-diode.

The Linux I2C software implements basically a complete I2C stack. This is because I wanted to have a little command line utility which does not need any special library or kernel module. It should just work on its own.

If you look into the file i2c_m.c (see download) you can see that really every I2C message is build bit by bit.

To generate the "bits" we must toggle the physical pins on the rc232 interface. This is done with ioctl calls:
        // set RTS pin:
        int arg=TIOCM_RTS;
        ioctl(fd, TIOCMBIS, &arg);
... or to produce a zero:
        // clear RTS pin:
        int arg=TIOCM_RTS;
        ioctl(fd, TIOCMBIC, &arg);
If you want to port this stack to a different OS then you just change these lines. The rest is plain C.  

USB to RS232

For laptops which do these days not have a rs232 interface you can simply use USB to rs232 adapter. I use e.g a no-name adapter which contains a Prolific 2303 chip. The adapter which I have looks like this in the /proc/bus/usb/devices file: Vendor=067b ProdID=2303 Rev= 2.02. See also "Use your ATEN UC-232A USB adapter with Linux (Linuxfocus, November 2001, article 223)".  

Conclusion

mount the sensor I am now using the thermometer for 2 month and I really like it because you can read it out directly on the display and you have the possibility to store all the data on your PC. You can view it there, draw graphs do statistics. Really cool.

The outdoor sensor must be protected properly against rain (and sun). You can try to wrap it into some plastic but I don't recommend this. No matter how tight you tie it, water will eventually come in and stay in there. The NTC is quite robust and it does not matter if it gets a bit humid as long as it can dry again. Use a up-side down mounted tablet tube which you leave open at the bottom. This way water will be able to get out again.


the thermometer


You can again order all parts (LCD display, PCB, microcontroller, ...) from the tuxgraphics online shop: shop.tuxgraphics.org.
Have fun!  

References



Webpages maintained by the LinuxFocus Editor team
© Guido Socher
"some rights reserved" see linuxfocus.org/license/
http://www.LinuxFocus.org
Translation information:
en --> -- : Guido Socher (homepage)

2005-03-01, generated by lfparser_pdf version 2.51